阿里云服务器网站目录,快乐无极网站,山东省工程建设管理信息网站,成都官方网站建设摘 要 连接座零件加工工艺及钻床夹具设计是包括零件加工的工艺设计、工序设计以及专用夹具的设计三部分。在工艺设计中要首先对零件进行分析#xff0c;了解零件的工艺再设计出毛坯的结构#xff0c;并选择好零件的加工基准#xff0c;设计出零件的工艺路线#xff1b;接着…摘 要连接座零件加工工艺及钻床夹具设计是包括零件加工的工艺设计、工序设计以及专用夹具的设计三部分。在工艺设计中要首先对零件进行分析了解零件的工艺再设计出毛坯的结构并选择好零件的加工基准设计出零件的工艺路线接着对零件各个工步的工序进行尺寸计算关键是决定出各个工序的工艺装备及切削用量然后进行专用夹具的设计选择设计出夹具的各个组成部件如定位元件、夹紧元件、引导元件、夹具体与机床的连接部件以及其它部件计算出夹具定位时产生的定位误差分析夹具结构的合理性与不足之处并在以后设计中注意改进。关键词工艺工序切削用量夹紧定位误差AbstractMicro centrifugal motor pump connecting seat parts processing technology and design of drilling jig design is the process design, including machining process design and fixture three. In the process of design should first understand the analysis of parts, parts of the process to design a blank structure, and choose the good components the processing datum, designs the process routes of the parts; then the parts of each labor step process size calculation, is the key to decide the craft equipment and the cutting process of the various design parameters; then the special fixture, the fixture selection for the various components of the design, such as connecting parts positioning device, clamping element, guiding element, clamp and machine tools and other components; positioning error is calculated when the fixture, analysis the rationality and shortcoming of fixture structure, improve and design in later.Keywords: process, process, cutting, clamping, positioning, error目 录摘 要 IIAbstract III第1章 序 言 1第2章 零件的分析 22.1零件的形状 22.2零件的工艺分析 3第3章 工艺规程设计 43.1 确定毛胚的制造形式 43.2 基面的选择 43.3 制定工艺路线 53.3.1 工艺路线方案一 53.3.2 工艺路线方案二 63.3.3 工艺方案的比较与分析 63.4 选择加工设备和工艺装备 83.4.1 机床选用 83.4.2 选择刀具 83.4.3 选择量具 83.5 机械加工余量、工序尺寸及毛坯尺寸的确定 83.5.1 外圆加工表面及端面 103.5.2 两孔的加工余量 103.6确定切削用量及基本工时 103.6.1 工序Ⅳ 113.6.2 工序Ⅴ 143.6.3 工序Ⅵ 143.6.4 工序Ⅶ 173.6.5 工序Ⅸ 173.6.6 工序Ⅹ 20第4章 钻床夹具设计 224.1 夹具的设计 224.1.1 定位分析 224.1.2 定位原理 224.1.3 定位元件的分析 234.1.4 夹紧元件的选择 234.1.5定位误差的分析 244.1.6切削力及夹紧力的计算 254.2 夹具设计及操作的简要说明 26总 结 27致 谢 28参 考 文 献 29